The contact owns a 2025 Mercedes Benz AMG GLA 35.  The contact stated while driving at 35 MPH on a green light,  the contact noticed another driver speeding over the limit on her left side which caused the other driver to collide with the contact's vehicle. The contact stated the other vehicle collided with the contact on the driver's side of the vehicle.  The contact lost control of the vehicle and crashed into a pole. The contact stated that none of the air bags deployed during the time of the accident.  The contact noticed that the other driver involved in the accident air bags were deployed.  No medical attention was provided but the contact sustained minor injuries the contact stated that the right side of their body was very sore and bruised. A police report was filed with the Cheltenham Police Department and a case was provided to the contact. The vehicle was towed to an independent mechanic for further investigation, the vehicle was not destroyed. The dealer was contacted and referred the contact to an independent mechanic for further assistance. Before the crash, the vehicle experienced shaking as the check engine warning light illuminated. The vehicle was taken toa dealer where the fuel injector was replaced. The manufacturer was made aware of the failure and a case was opened. The approximate failure mileage was 150.  

The contact owns a 2021 Mercedes-Benz GLA250W4. The contact stated that while parking his vehicle when he went to apply the brake pedal, the brakes did not engage. The contact stated that the vehicle then crashed into the wall, however, the air bags did not deploy. The contact stated that the warning light illuminated after the crash indicating that the brakes are now operational. The contact stated that there was no police report made, however, the 2 passengers did seek medical attention. The contact stated he was able to drive his vehicle home, however, the dealer did have the car towed days later and it remains for repair. The contact stated the dealer advised him to contact the manufacturer, as he did to file a complaint. The failure mileage was 9,429. 

Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see picture file in attachment Outer joint housing before) before coating with Molykote, using spirit (free of dust and grease) 3. Coat contact surface A (see image file in attachment Outer joint housing after) using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir or shake it well (for at least 1 minute).

Complaint USB port not functioning properly. Cause Most reported USB port issues are due to improper use or contamination. Note: Any repair costs must be discussed with the customer beforehand. Common external factors identified include: • Fluid intrusion • Broken bushings or physical damage See attachments. Remedy If a component needs replacement but shows no visible external damage, submit a detailed TIPS case only when technical support is required. Include details of all connected external devices (such as charging cables, USB drives, and hard drives). If diagnostic results directly indicate component replacement, a TIPS case is not necessary.

Complaint USB port not functioning properly. Cause Most reported USB port issues are due to improper use or contamination. Note: Any repair costs must be discussed with the customer beforehand. Common external factors identified include: • Fluid intrusion • Broken bushings or physical damage See attachments. Remedy If a component needs replacement without visible external damage, submit a detailed TIPS case. Include information on all connected external devices (e.g., charging cables, USB drives, hard drives).

Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the 48-V on-board electrical system battery software might not meet current production specifications. A communication error may occur when reactivating the 48V lithium-ion battery during reinitialization. The system might detect and store this error, causing the malfunction indicator lamp to illuminate unnecessarily. Remedy  MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update 48-V onboard electrical system battery software.

Complaint Instrument cluster message 4MATIC inoperative. The following fault code may be present in all-wheel drive control unit N15/17: P147354 - Erroneous adaptation of the transfer case. The calibration is missing. P14759A - The coupling of the transfer case has malfunctioned. The operating conditions for the component or the system have not been fulfilled. Cause Coupling of the rear axle differential has reached the wear limit or a coupling issue is present. Remedy Please read off the part number of the rear axle differential installed on the vehicle and check the table below to determine if the differential can be repaired with a clutch repair kit. The table below is also in attachments. (If needed, check validity for further clarification of model designations). Complaint Instrument cluster message 4MATIC inoperative. The following fault code may be present in all-wheel drive control unit N15/17: P147354 - Erroneous adaptation of the transfer case. The calibration is missing. P14759A - The coupling of the transfer case has malfunctioned. The operating conditions for the component or the system have not been fulfilled. Cause Coupling of the rear axle differential has reached the wear limit or a coupling issue is present. Remedy Please read off the part number of the rear axle differential installed on the vehicle and check the table below to determine if the differential can be repaired with a clutch repair kit. The table below is also in attachments. (If needed, check validity for further clarification of model designations)

Complaint At low speeds and light brake pressure, brakes will make a groaning or honking noise. Cause Frictional vibrations with very light brake pressure/modulations. Remedy This condition can be duplicated on most vehicles. To validate, use a like for like reference vehicle. The noise is normal behavior under the conditions listed. With very light brake pressure this noise can be induced/caused due to normal brake pad and brake rotor vibrations. Exchanging brake components will not rectify.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Note: In this case, do not use the damage codes for the speakers in the warranty claim.

Complaint The check engine light illuminates or the 48 V message is displayed in the instrument cluster Cause Fault code P0A7F00 stored in the 48 V battery G1/3 and/or is current. Remedy Update the 48V battery to SW 25/12 A0019020424 Then perform the following measures: - Switch on ignition - Read out actual value 209 in XENTRY Diagnosis for G1/3 (48 V battery) State of Health Capacity-SOHC -- If the value > 80% doesn't require a healing process -- If the value is < 80%, continue with the following steps Carry out capacity healing procedures: - Discharge 48 V battery in vehicle with ignition On and check the SOC of the 48 V battery in the workshop menu of the instrument cluster - At SOC <30%: Stop discharge and lock vehicle - with key out of range; (Bus idle) -Charging the 48V battery - When SOC reaches or exceeds 70%, stop charging and lock the vehicle with the key out of range; (bus idle) - After 1.5h bus idle: Switch on ignition Read out actual value 209 in XENTRY Diagnosis in the G1/3 (48 V battery) State of Health Capacity-SOHC - SOH > 90%: Procedure is finished and fault memory erased - SOH < 90%: Repeat the steps again. If the value is still too low after 5 repetitions: Abort healing process and open a TIPS case.

Complaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy 1) If the battery is discharged, charge the battery. Review WS54.00-P-0037B for minimum charger specifications. • Note the amperage difference between trickle (maintainer) chargers of at least 16A and quick chargers of at least 30A. • Review AP54.10-P-5449U. Note when battery is sufficiently charged the charger current is less 5A. 2) While charging the battery, analyze the vehicle data to determine root cause of discharge using the following data points: • NOTE: For guidance on use of the on-board electrical data please review the AKUBIS video titled New onboard electrical system diagnosis shown on BR 166. The video can be accessed through WIS by following the path WSM--> content by model series --> passenger cars --> ML-Class --> Model 166 --> group 54 --> New onboard electrical system diagnosis. • Refer to the March 2023 PCTT for the video walkthrough of analysis as well as the attachment of the slides to this Li. • Review GF54.10-P-1012A regarding what can cause deep discharge protection to not end a battery draw. • Review SI54.10-P-0024A for proper maintenance of the vehicle. For Star 2 vehicles: -Review FSAM on-board electrical data conspicuous records • NOTE: This data can be found via FSAM N10/6 -> Actual Values -> On-board electrical system -> On-board electrical system data For Star 3 vehicles: -Review N73/3 EZS on-board electrical data conspicuous records • NOTE: This data can be found via EZS N73/3 -> Actual Values -> On-board electrical system -> On-board electrical system data 3) Determine if root cause is due to: • vehicle technical issue? • customer behavior? NOTE: Recommend using battery analysis sheet found in XiW -> Local Contents -> Diagnostic info -> Battery Discharge Worksheet 4) If battery still does not accept charge AND the vehicle does not fall within the parameters of improper maintenance, then create a TIPS case. *IMPORTANT* - If the improper maintenance/use is found during diagnosis, DO NOT open a TIPS case. If a TIPS case is opened, it will be marked 1 star and directed to your assigned FSE for review. TIPS Case must include with the case: • Amperage setting of charger and time battery was on charger • XENTRY Battery Tester results • Voltage of battery taken with multimeter: Do not connect charger while taking measurements • N10/6 FSAM, (N73 or N73/3) and (N73*1 or N73/3*1) • Workshop analysis of conspicuous data • Root cause analysis for battery discharge based on the above documents (technical, customer, etc.) • NOTE: For expedited results when creating a case write customer complaint as XENTRY Battery Tester implausible. 

Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy For vehicles with 722.9 transmission: Ensure LI54.15-P-057373 is performed before replacing any component parts. After processing and complying with the above document(s): 1. Perform an ignition reset on Y3/8n4 (VGS) 2. Inspect transmission connector for loose connections, damaged wiring or pins and any other concerns If communication with the VGS cannot be established, the complete valve body ('electrohydraulic controller unit (EHS)') must be replaced. Installation of a VGS repair kit is not permitted in this case as it is not possible to transfer the necessary valve characteristics without communication with the original control unit.

Mercedes-Benz GLA35 AMG

Filing history

Reported severity

Top reported issues — Mercedes-Benz GLA35 AMG

Recent filings